How to copy preset from a video to an other video

[eliasuke]

Hi,

Sorry for my verry bad english, but I'll try to do my best.

I would like copy this preset for converting an other video with the same, but I don't know how to do this

The preset :


Format : MPEG-4
Format profile : Base Media
Codec ID : isom
File size : 49.3 MiB
Duration : 22mn 44s
Overall bit rate : 303 Kbps
Encoded date : UTC 2010-07-23 14:15:14
Tagged date : UTC 2010-07-23 14:15:14

Video
ID : 1
Format : AVC
Format/Info : Advanced Video Codec
Format profile : High@L5.1
Format settings, CABAC : Yes
Format settings, ReFrames : 8 frames
Codec ID : avc1
Codec ID/Info : Advanced Video Coding
Duration : 22mn 44s
Bit rate mode : Variable
Bit rate : 268 Kbps
Maximum bit rate : 1 594 Kbps
Width : 1 280 pixels
Height : 720 pixels
Display aspect ratio : 16:9
Frame rate mode : Constant
Frame rate : 23.976 fps
Resolution : 8 bits
Colorimetry : 4:2:0
Scan type : Progressive
Bits/(Pixel*Frame) : 0.012
Stream size : 43.6 MiB (89%)
Writing library : x264 core 56 svn-676
Encoding settings : cabac=1 / ref=5 / deblock=1:1:1 / analyse=0x3:0x133 / me=umh / subme=6 / brdo=1 / mixed_ref=1 / me_range=16 / chroma_me=1 / trellis=1 / 8x8dct=1 / cqm=0 / deadzone=21,11 / chroma_qp_offset=0 / threads=3 / nr=0 / decimate=1 / mbaff=0 / bframes=5 / b_pyramid=1 / b_adapt=1 / b_bias=0 / direct=1 / wpredb=1 / bime=1 / keyint=250 / keyint_min=25 / scenecut=40(pre) / rc=2pass / bitrate=268 / ratetol=1.0 / rceq='blurCplx^(1-qComp)' / qcomp=0.60 / qpmin=10 / qpmax=51 / qpstep=4 / cplxblur=20.0 / qblur=0.5 / ip_ratio=1.40 / pb_ratio=1.30
Encoded date : UTC 2010-07-23 14:15:14
Tagged date : UTC 2010-07-23 14:15:19

Audio
ID : 2
Format : AAC
Format/Info : Advanced Audio Codec
Format version : Version 4
Format profile : LC
Format settings, SBR : Yes
Format settings, PS : Yes
Codec ID : 40
Duration : 22mn 44s
Bit rate mode : Variable
Bit rate : 32.0 Kbps
Maximum bit rate : 35.7 Kbps
Channel(s) : 2 channels
Channel positions : Front: L R
Sampling rate : 48.0 KHz
Stream size : 5.21 MiB (11%)
Encoded date : UTC 2010-07-23 14:15:19
Tagged date : UTC 2010-07-23 14:15:19



I don't know how to change the Container Bitrate and some other settings. Is it in Media Coder, a function that create y the XML preset from a video ?

[encroder]

To save or load a preset use File > Save or Load A Preset options

If have two videos to transcode and are loaded into mediacoder, the current settings you have set will be used for both.

Dending on State > Done or Undone. These States can be chosen using the Set Item State, when the right mouse button is clicked on a loaded file name.

[meRobs]

eliasuke: welcome to the Forum!
What you have listed is not a Preset. It is merely a listing of properties for a file from MediaInfo.
For a discussion on setting a Preset, see: viewtopic.php?f=17&t=8131
Also, you might like to learn more by reading the Tips & Guides section (link below).

And to set up MediaCoder to get a simliar set of file characteristics, you only need to set some basic values on the main tabs, the Video, Audio, Picture and Container tabs.
When I get time later today I will experiment to get an MP4 file with similar features and let you know!

[meRobs]

Have just converted a file into another with approximately the same results in MediaInfo.
I used:
Video tab: Format/Mode/Source/Encoder = H264/varaible at 50/FFmpeg/Auto select
and at right: Profile=High, Level=5.1, Preset=medium and B-frames=3
Audio tab: Encoder/Format/Source/Resample = FAAC/LC-AAC/Auto/48000 Hz
and at right: Average bitrtae = 32, MPEG4 checked and AAC in the lower panel
Container tab: MP4 as container and the Multiplexer = auto
Picture tab: Resize=128x720, Frame rate = 24000/1001 (becomes 23.976) and Set Display AR = 16:9.

I don't know why you need to have the parameters the same, especially since the video bitrate is awfully low for the frame size of 1280x720, which is a lot of pixels to be described with very few bits of info. Similarly the audio bitrate is a bit low. But that is up to you. If the qality of either is OK for your purposes, then fine. Otherwise increase them.
Experiment!